Midmark M9D AutoClave Automatic Sterilizer (Manual Door)

The Midmark M9D AutoClave Automatic Sterilizer offers easy, effective sterilization but without the convenience of a door that opens automatically. One button starts the cycle... but at the end of the automatic sterilization process, you need to manually open the door within 30 minutes of completion to activate the dry cycle. This extra step is the only physical difference between the Midmark M9D and its automatic counterparts.

Convenience at a glance

The LCD display indicates cycle selected, cycle temperature and exposure time. When the cycle enters sterilization mode and dry mode, the remaining cycle time is displayed as well as temperature and pressure.

No more wet instruments

Once the sterilization is complete, the door opens automatically and quietly to dissipate steam and dry your instruments. You’ll have dry, sterile instruments every time.

Safety features

If the door is not closed completely or the reservoir water level is low, the LCD display will provide the appropriate message. In either case, sterilization can’t continue until you’ve attended to the unit.

Ease of draining & filling

For ease of draining and filling, the Midmark M9’s reservoir fill port and drain tube are in the front of the unit, not on top or in back.

Self Program Controls

Programmable controls allow for creation of different cycle parameters for special sterilization needs. Programmable buttons allow you to change the following: Time (3 to 90 minutes), Temperature (230 to 275˚F), Dry Time (0 to 60 minutes), or Vent (slow or fast). The #1 and #2 buttons allow you to store the change if desired.

Pre-Programmed Controls

Four pre-programmed sterilization cycle controls: Unwrapped (132º C or 270º F for 3 minutes), Pouched (132º C or 270º F for 5 minutes), Packs (121º C or 250º F for 30 minutes), Handpiece (unwrapped and pouched) (132˚ C or 270˚ F for 6 minutes).

Pouch Rack

1 pouch rack

Specifications:

• Overall length w/plug: 20.13" (51 cm)
• Overall width: 15.3" (38.9 cm)
• Overall height w/printer: 15.8" (40.1 cm)
• Countertop area: 15.3" x 20.38" (38.9 cm x 51.8 cm)
• Chamber:
  • 9" diameter (22.9 cm)
  • 15" depth (38.0 cm)
  • 3.5 gal. usable volume (13.4 liters)
• Trays:
  • Two large – 7 5/16" W x 12" L x 7/8" D (18.6 cm x 30.5 cm x 2.2 cm)
  • Two small – 5 5/8" W x 12" L x 7/8" D (14.3 cm x 30.5 cm x 2.2 cm)
• Unit weight: 73 lbs. (33.1 kg)
• Shipping weight: 81 lbs. (36.7 kg)
• Water reservoir capacity: 1.1 gal. (4.1 liters)

Electrical Requirements:

• 115 VAC, 50/60 Hz, 15 AMPS Single Phase
• 115 VAC has 1425-watt tubular immersion heater
• 230 VAC, 50/60 Hz, 10 AMPS Single Phase
• 230 VAC has 1500-watt tubular immersion heater
• UL61010A-1, UL61010A-2-041
• CAN/CSA C22.2 No. 1010
• CAN/CSA C22.2 No. 1010.2-041 96
• A separate (dedicated) circuit is recommended for this sterilizer
• Meets the requirements of ASME Boiler and Pressure Vessel Code

Optional Accessory:

• Impact Dot Matrix Printer
• Sterilizer Deep Tray
• Sterilizer Pouch Rack
• Cool Hand Tool (Tray & Cassette Removal Tool)
• External Condensing Tank
• SpeedClean 16 oz. (1 case-12 bottles)
• SpeedClean 32 oz. (1 case-12 bottles)

Installation: Use on Formica®, stainless steel or stone surface. Allow 2.5" (6.4 cm) on sides and rear and 12" (30.5 cm) above, to allow space to fill reservoir and for cooling processed trays.